Mitsubishi MOTION CONTROLLERS Q173DCPU Manuál s instrukcemi stáhnout pdf (Strana 39)

2 - 10

2 SYSTEM CONFIGURATION

(3) Other restrictions

(a) Motion CPU module cannot be set as the control CPU of intelligent function

module (excluding some modules) or Graphic Operation Terminal(GOT).

(b) Be sure to use the battery.

• Use a EMI connector of Motion CPU module

• Use a device set in the forced stop input setting of system setting

(d) Forced stop input for EMI connector of Motion CPU module cannot be

invalidated by the parameter.

When the device set in the forced stop input setting is used without use of

EMI connector of Motion CPU module, apply 24VDC voltage on EMI

connector and invalidate the forced stop input of EMI connector.

(e) Be sure to use the cable for forced stop input (sold separately). The forced

stop cannot be released without using it.

(f) Set "SSCNET

/H" or "SSCNET " for every line in the SSCNET setting of

system setting to communicate with the servo amplifiers.

MR-J4(W)-

B can be used by setting "SSCNET /H", and MR-J3(W)- B

can be used by setting "SSCNET

QDS

(g) There are the following restrictions when "SSCCNET

" is set as

communication method.

When the operation cycle is 0.2[ms], set the system setting and the axis

select rotary switch of servo amplifier to "0 to 3".

If the axis select rotary switch of servo amplifier is set to "4 to F", the servo

amplifiers are not recognized.

QDS

When the operation cycle is 0.4[ms], set the system setting and the axis

select rotary switch of servo amplifier to "0 to 7".

If the axis select rotary switch of servo amplifier is set to "8 to F", the servo

amplifiers are not recognized.

There is no restriction when "SSCNET

/H" is set in the SSCNET setting.

(Note): The setting of axis select rotary switch differs according to the servo

amplifier. Refer to the "Servo amplifier Instruction Manual" for details.

(h) Maximum number of control axes of servo amplifier is shown below.

• Operation cycle is 0.2[ms]: 4 axes per line

• Operation cycle is 0.4[ms]: 8 axes per line

There is no restriction when "SSCNET

/H" is set in the SSCNET setting.

QDS

(i) When the operation cycle is "default setting", the operation cycle is set

depending on the number of axes used. However, when "SSCNET

" is set

in the SSCNET communication setting and the number of axes used of

servo amplifier is 9 axes or more per line, the operation cycle of 0.8 [ms] or

more is set. (Refer to Section 2.5.1(6).)

QDS

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 251 252

Komentáře k této Příručce

Žádné komentáře

Modèles	Type de document
CRP762/01	Fiche technique Philips Docking station CRP762, 2 pages
CRP767/01	Fiche technique Philips Front wheel CRP767, 2 pages
CRP745/01	Fiche technique Philips PowerPro Inlet filter CRP745, 2 pages
CRP764/01	Fiche technique Philips Dust container cover CRP764, 2 pages
CRP789/01	Fiche technique Philips SilentStar Hose CRP789, 2 pages
CRP784/01	Fiche technique Philips DailyDuo Vacuum cleaner filter CRP784, 2 pages
CRP756/01	Fiche technique Philips EasyStar Rechargeable Ni-Mh battery CRP756, 2 pages
CRP760/01	Fiche technique Philips Roller Brush CRP760, 2 pages
CRP743/01	Fiche technique Philips PowerPro Telescopic Tube for vacuum cleaner CRP743, 2 pages
CRP781/01	Fiche technique Philips Rechargeable Li-Ion battery CRP781, 2 pages
CRP739/01	Fiche technique Philips PowerPro Accessory clip CRP739, 2 pages
CRP768/01	Fiche technique Philips Brush retainer CRP768, 2 pages
CRP777/01	Fiche technique Philips Rechargeable Li-on battery CRP777, 2 pages
CRP761/01	Fiche technique Philips Set of side brushes CRP761, 2 pages
CRP754/01	Fiche technique Philips EasyStar Filter CRP754, 2 pages
CRP786/01	Fiche technique Philips Inlet filter frame CRP786, 2 pages
FC6010/01	Fiche technique Philips Vacuum cleaner nozzle FC6010, 2 pages
CRP415/01	Fiche technique Philips PowerLife Motor protection filter CRP415, 2 pages
CRP414/01	Fiche technique Philips Hose CRP414, 2 pages
CRP192/01	Fiche technique Philips Marathon Bucket CRP192, 2 pages

Mitsubishi MOTION CONTROLLERS Q173DCPU Manuál s instrukcemi Strana 39

Komentáře k této Příručce

Philips CP9986/01 manuels

Philips CP9986/01 Fiche technique (2 pages)

Table des matières

Plus de produits et de manuels pour Non Philips

Mitsubishi MOTION CONTROLLERS Q173DCPU Manuál s instrukcemi Strana 39

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q173DCPU

Philips CP9986/01 manuels

Philips CP9986/01 Fiche technique (2 pages)

Table des matières

Plus de produits et de manuels pour Non Philips