Mitsubishi MOTION CONTROLLERS Q172DCPU Uživatelský manuál Strana 39
- Strana / 192
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2 - 18
2 SYSTEM CONFIGURATION
2.3 General Specifications
General specifications of Q173DCPU/Q172DCPU module are shown below.
Item Specification
Operating ambient temperature 0 to 55°C (32 to 131°F)
Storage ambient temperature -25 to 75°C (-13 to 167°F)
(Note-3)
Operating ambient humidity 5 to 95% RH, non-condensing
Storage ambient humidity 5 to 95% RH, non-condensing
Frequency Acceleration Amplitude Sweep count
10 to 57Hz ——
0.075mm
(0.003inch)
Under intermittent
vibration
57 to 150Hz 9.8m/s
2
——
10 to 57Hz ——
0.035mm
(0.001inch)
Vibration resistance
Under continuous
vibration
57 to 150Hz 4.9m/s
2
——
10 times each
in X, Y, Z
directions
(For 80 min.)
Shock resistance 147m/s
2
, 3 times in each of 3 directions X, Y, Z
Operating ambience No corrosive gases
Operating altitude 2000m(6561.68ft.) or less
Mounting location Inside control panel
Overvoltage category
(Note-1)
II or less
Pollution level
(Note-2)
2 or less
(Note-1) : This indicates the section of the power supply to which the equipment is assumed to be connected between the
public electrical power distribution network and the machinery within premises.
Category
applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the rated voltage of 300V is 2500V.
(Note-2) : This index indicates the degree to which conductive material is generated in terms of the environment in which
the equipment is used.
Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity caused by condensing
must be expected occasionally.
(Note-3) : Do not use or store the Motion controller under pressure higher than the atmospheric pressure of altitude 0m.
Doing so can cause an operation failure.
CAUTION
The Motion controller must be stored and used under the conditions listed in the table of
specifications above.
When not using the module for a long time, disconnect the power line from the Motion controller
or servo amplifier.
Place the Motion controller and servo amplifier in static electricity preventing vinyl bags and store.
When storing for a long time, please contact with our sales representative.
Also, execute a trial operation.
- Q173DCPU 1
- Q172DCPU 1
- SAFETY PRECAUTIONS 2
- For Safe Operations 3
- 2. For fire prevention 3
- 3. For injury prevention 4
- 4. Various precautions 4
- (4) Wiring 8
- (6) Usage methods 9
- Electro 10
- (10) General cautions 11
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 18
- 1 OVERVIEW 19
- 2. SYSTEM CONFIGURATION 22
- 2 SYSTEM CONFIGURATION 23
- (Note-3) 32
- (Note-4) 33
- (Note-5) 33
- (Note-6) 33
- (Note-7) 34
- Model name Software package 38
- GX Developer SW8D5C-GPPW-E 38
- , non-condensing 39
- (1) Q173DCPU/Q172DCPU 40
- (2) 7-segment LED display 42
- (4) Operation mode 44
- Item Q173DCPU Q172DCPU 45
- Mass [kg] 0.33 0.33 45
- 2.4.2 Power supply module 48
- 100-240VAC 52
- 5V = 0.33 + 1.25 + 0.05 55
- 812345670 58
- I/O Allocations 58
- (1) Q172DLX name of parts 59
- (a) Module specifications 60
- (b) Input 60
- (a) Servo external signals 61
- • Tracking enable signal 67
- Wiring example 69
- (Note-1), (Note-2) 70
- (a) Specifications 71
- Battery Specifications 71
- (b) Battery replacement 71
- (1) Q173DPX name of parts 73
- (Duty ratio: 50% 25%) 79
- 20 s or more 79
- A4 A3 A2 80
- B4 B3 B2 80
- 2.4.9 External battery 89
- 3. DESIGN 94
- 3.2 External Circuit Design 97
- 3 DESIGN 100
- (2) Grounding 101
- 3.2.2 Safety circuit design 102
- (2) Emergency stop circuit 102
- (3) Forced stop circuit 102
- <Input module QX10> 103
- 3.3.1 Mounting environment 104
- CAUTION 105
- 5V 106
- (Q173DCPU use) 108
- 3.4 Design Checklist 109
- 4. INSTALLATION AND WIRING 110
- 4 INSTALLATION AND WIRING 111
- and large current) 111
- (1) Fitting dimensions 112
- DIN rail 113
- (2) Mounting surface 118
- Motion CPU 119
- 4.2.2 Battery cable 122
- Motion CPU module 124
- Coupling 126
- 4.4 Wiring 127
- (1) Power supply wiring 127
- (3) Grounding 129
- of 2 mm 129
- (Note-1) 130
- Terminal 131
- Solderless terminals 131
- (1) Minimum bend radius 132
- (2) Tension 132
- (3) Lateral pressure 132
- CAUT I ON 133
- STOP RUN 133
- (Note-1) 133
- [Servo data setting] 139
- Turn ON power supply again 139
- Shipped from the factory in 142
- 6.1 Maintenance Works 145
- Electromagnetic 146
- 6.2 Daily Inspection 147
- Table 6.1 Daily Inspection 147
- 6.3 Periodic Inspection 148
- 6.4 Life 149
- Table 6.3 Life 149
- 6.5 External Battery 150
- 6.5.1 Battery life 151
- Battery connector for Q6BAT 153
- Battery(Q6BAT) 153
- Lead wire 153
- MITSUBISHI 154
- LITHIUM BATTERY 154
- RUN/STOP/RESETand 160
- RUN/STOP switch of CPU 160
- No.1 and target CPU Module 160
- 6.6.3 Confirming error code 168
- DC input 169
- (plus common) 169
- Input module 169
- Output module 171
- Leakage current 171
- APPENDICES 172
- (Note-2) 175
- :Twisted pair cable 176
- Type : Q170DBATCBL M 177
- Type : Q170DEMICBL M 178
- 119.3(4.70) 27.4(1.08) 179
- 98(3.86) 179
- 27.4(1.08) 179
- 119.3(4.70) 179
- PPENDICES 180
- (2) Q64P 182
- WARRANTY 189
- MOTION CONTROLLER Qseries 190
- MITSUBISHI ELECTRIC 192
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q172DCPU
Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q172DCPU Uživatelský manuál
(8 stránky)
(8 stránky)
Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q172DCPU Specifikace
(88 stránky)
(88 stránky)
Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q172DCPU Manuál s instrukcemi
(316 stránky)
(316 stránky)
Bezpečnostní systémy pro řízení přístupu Mitsubishi MOTION CONTROLLERS Q172DCPU Manuál s instrukcemi
(174 stránky)
(174 stránky)
(90 stránky)Philips CP9986/01 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Philips CP9986/01.
Nous fournissons des manuels en pdf 1 Philips CP9986/01 à télécharger gratuitement par type de document : Fiche technique
Komentáře k této Příručce