Mitsubishi GT11 Specifikace stáhnout pdf (Strana 2)

3.3 Built-in Interface Specifications

3.4 Power Supply Specifications

*1 The GOT continues to operate even upon 5ms or shorter instantaneous power failure.

The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.

*2 A surge absorber is connected between the power supply and earth terminal so that the GOT does not malfunction due to applied lightning surge noise.

Values without a surge absorber are described for the dielectric withstand voltage and the insulation resistance.

3.5 External Dimensions

Item

Specifications

GT1155-QTBDQ

GT1155-QSBDQ

GT1150-QLBDQ

GT1155-QTBDA

GT1155-QSBDA

GT1150-QLBDA

Built-in

interface

BUS

Bus interface for connecting to the QCPU (Q mode) and motion

controller CPU (Q series) 1ch

Application : For communicating with a programmable controller

Bus interface for connecting to the QnACPU, ACPU, and motion

controller CPU (A series) 1ch

Application : For communicating with a programmable controller

RS-232

Conforming to serial RS232 standard, 1ch

Transmission speed: 115,200/57,600/38,400/19,200/9,600/4,800bps

Connector shape : D-sub 9-pin (Male)

Application : Bar code reader connection, Personal computer communication

(Project data upload/download, OS installation, transparent function)

USB

Conforming to serial USB (Full Speed 12Mbps), device, 1ch

Application: Personal computer communication (Project data upload/download, OS installation, transparent function)

CF card

Conforming to PCMCIA, compact flash slot, 1ch

Connector shape : Dedicated for TYPE I

Application : Data transfer, data storage

Item

Specifications

GT1155-QTBDQ

GT1155-QTBDA

GT1155-QSBDQ

GT1155-QSBDA

GT1150-QLBDQ

GT1150-QLBDA

Input power supply voltage 24VDC (+10% -15%), ripple voltage 200mV or less

Fuse (built-in, not exchangeable) 1.0A

Power consumption 11.16W (465mA/24VDC) or less 9.72W (405mA/24VDC) or less 7.92W (330mA/24VDC) or less

At backlight off 5.04W (210mA/24VDC) or less

Inrush current 26A or less (26.4V) 4ms

Permissible instantaneous power

failure time

Within 10ms

Noise immunity Noise voltage: 500Vp-p, Noise width: 1s (by noise simulator of 25to 60Hz noise frequency)

Dielectric withstand voltage

500VAC for 1 minute (across power supply terminals and earth)

Insulation resistance

10M or larger by a 500VDC insulation resistance tester (across power supply terminals and earth)

Applicable wire size

0.75 to 2[mm

]

Applicable solderless terminal Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A

Applicable tightening torque

(Terminal block terminal screw)

0.5 to 0.8[N



167 (6.58)

28.5

(1.13)

21 (0.83)

135 (5.32)

62 (2.44)

6 (0.24)

48 (1.89)

65 (2.56)

(0.40)

120

(4.73)

(0.40)

110 (4.33)

#4-40UNC

(Inch screw

type)

Panel thickness:

5mm(0.2") or less

152 (5.99)

28.5

(1.13)

110 (4.33)

167 (6.58)

28.5

(1.13)

21 (0.83)

135 (5.32)

62 (2.44)

6 (0.24)

48 (1.89)

65 (2.56)

(0.40)

120

(4.73)

(0.40)

110 (4.33)

(Metric screw

type)

#4-40UNC

(Inch screw type)

Panel thickness:

5mm(0.2") or less

Unit: mm (inch)

152 (5.99)

28.5

(1.13)

110 (4.33)

(0.16)

(0.20)

GT1155-QTBDA, GT1155-QSBDA, GT1150-QLBDAGT1155-QTBDQ, GT1155-QSBDQ, GT1150-QLBDQ

(0.16)

(0.20)

4. EMC AND LOW VOLTAGE DIRECTIVE

For the products sold in European countries, the conformance to the EMC Directive,

which is one of the European Directives, has been a legal obligation since 1996.

Also, conformance to the Low Voltage Directive, another European DIrectives, has

been a legal obligation since 1997.

Manufacturers who recognize their products must conform to the EMC and Low

Voltage Directive are required to declare that their products conform to these

Directives and put a "CE mark" on their products.

 Authorized representative in Europe

Authorized representative in Europe is shown below

Name :Mitsubishi Electric Europe BV

Address:Gothaer strase 8, 40880 Ratingen, Germany

4.1 Requirements for Conformance to EMC Directive

The EMC Directive specifies that products placed on the market must "be so con-

structed that they do not cause excessive electromagnetic interference (emis-

sions) and are not unduly affected by electromagnetic interference (immunity)".

The applicable products are requested to meet these requirements.

The sections 4.1.1 through 4.1.3 summarize the precautions on conformance to

the EMC Directive of the machinery constructed using the GOT.

The details of these precautions has been prepared based on the requirements

and the applicable standards control.

However, we will not assure that the overall machinery manufactured according to

these details conforms to the above-mentioned directives.

The method of conformance to the EMC Directive and the judgment on whether or

not the machinery conforms to the EMC Directive must be determined finally by

the manufacturer of the machinery.

4.1.1 Standards applicable to the EMC Directive

The following products have shown compliance through direct testing (to the iden-

tified standards) and design analysis (forming a technical construction file) to the

European Directive for Electromagnetic Compatibility (89/336/EEC) when used as

directed by the appropriate documentation

Type :Programmable Controller (Open Type Equipment)

Models :MELSEC GOT series products, identified here, manufactured from

January 7th, 2008

GT1155-QTBDQ, GT1155-QTBDA, GT1155-QSBDQ, GT1155-QSBDA,

GT1150-QLBDQ, GT1150-QLBDA (For this product see note under and

over the page).

4.1.2 Control cabinet

The GOT is an open type device (device installed to another device) and must be

installed in a conductive control panel or cabinet.

It not only assure the safety but also has a large effect to shut down the noise gen-

erated from GOT, on the control panel.

1) Control cabinet

a) Use a conductive control cabinet.

b) When attaching the control cabinet's top plate or base plate, mask paint-

ing and weld so that good surface contact can be made between the

cabinet and plate.

c) To ensure good electrical contact with the control cabinet, mask the

paint on the installation bolts of the inner plate in the control cabinet so

that contact between surfaces can be ensured over the widest possible

area.

d) Earth the control cabinet with a thick wire so that a low impedance con-

nection to ground can be ensured even at high frequencies. (22mm 2

wire or thicker is recommended.)

e) Holes made in the control cabinet must be 10 cm (3.94”) diameter or

less. If the holes are 10cm (3.94”) or larger, radio frequency noise may

be emitted.

In addition, because radio waves leak through a clearance between the

control panel door and the main unit, reduce the clearance as much as

practicable.

The leakage of radio waves can be suppressed by the direct application

of an EMI gasket on the paint surface.

2) Connection of power and ground wires

Ground and power supply wires for the GOT must be connected as described

below.

a) Provide an earthing point near the GOT. Earth the power supply's FG

terminal (FG: Frame Ground) with the thickest and shortest wire possi-

ble. (The wire length must be 30cm (11.18”) or shorter.)

The FG terminal function is to pass the noise generated in the GOT to

the ground, so an impedance that is as low as possible must be

ensured. As the wires are used to relieve the noise, the wire itself carries

a large noise content and thus short wiring means that the wire is pre-

vented from acting as an antenna.

Note) A long conductor will become a more efficient antenna at high fre-

quency.

3) Electrical shock prevention

In order to such as the operators from electric shocks, the control box must have

the following functions :

a) The control cabinet must be equipped with a lock so that only skilled or

qualified personnel.

b) The control cabinet must be fitted with advice which automatically stops

the power supply when the cabinet is opened.

4) Dustproof and waterproof features

The control box also has the dustproof and waterproof functions. Insufficient

dustproof and waterproof features lower the insulation withstand voltage, resulting

in insulation destruction.

The insulation in our GOT is designed to cope with the pollution level 2, so use in

an environment with pollution level 2 or better.

Pollution level 1:An environment where the air is dry and conductive dust does

not exist.

Pollution level 2:An environment where conductive dust does not usually exist,

but occasional

temporary conductivity occurs due to the accumulated dust.

Generally, this is the level for inside the control box equivalent a

control room or on the floor of a typical factory.

Pollution level 3:An environment where conductive dust exits and conductivity

may be generated due to the accumulated dust.

An environment for a typical factory floor.

Pollution level 4:Continuous conductivity may occur due to rain, snow, etc.

An outdoor environment.

4.1.3 Grounding

It is necessary to use the GOT grounding terminal only when it is in the grounded

condition.

Be sure to ground the grounding for the safety reasons and EMC Directives.

Functional grounding : Improves the noise resistance.

Standard Remark

EN61131-2 : 2007

Programmable controllers

- Equipment, requirement and tests

EMI

Compliance with all relevant

aspects of the standard.

(Radiated Emissions)

EMS

Compliance with all relevant

aspects of the standard.

(ESD,RF electromagnetic field,

EFTB, Surge, RF conducted

disturbances and Power

frequency magnetic field)

4.2 Wiring Precautions the Part which Matches the EMC

Directives

Connect and wire GOT equipment as instructed below.

If the GOT equipment is configured in a way that differs from the following

instructions then the system will not comply with EMC directives.

4.2.1 About the cable used

Connect and wire GOT equipment as instructed below.

If the GOT equipment is configured in a way that differs from the following

instructions then the system will not comply with EMC directives.

Bus connection cable

The following products are used in the EMC specification compatibility test con-

ducted by Mitsubishi Electric Corporation.

 ZCAT3035-1330 ferrite core manufactured by TDK corporation

 AD75CK-type cable clamp manufactured by MITSUBISHI

 Zipper tube SHNJ type manufactured by Zippertubing(Japan),Ltd.

EX.1

EX.2

EX.3

GOT

Unit

Existing Cables User Made Cables

GT1155-

QTBDQ,

GT1155-

QSBDQ,

GT1150-

QLBDQ

GT15-QC B,GT15-QC BS modified as

shown in EX.1.

Peel the sheath at both ends of the cable,

and expose the shield braided wire for

grounding. (For grounding with

clamps.(refer to Section 4.2.3.))

The cable need to

be independently

tested by the user

to demonstrate

EMC compatibility

when they are used

with the GOT, the

PLC of MELSEC-Q

series, MELSEC-

QnA series, and

MELSEC-A series.

GT1155-

QTBDA,

GT1155-

QSBDA.

GT1150-

QLBDA

GT15-C BS,cGT15-C EXSS-S1

modified as shown in EX.2.

Peel the sheath at both ends of the cable,

and expose the shield braided wire for

grounding. (For grounding with

clamps.(refer to Section 4.2.3.))

Other bus connection cables modified as

shown in EX.3.

Wind cable shield material around the

cable, and pull out the grounding braided

wire of the cable shield material.

Attach the ferrite core to the cable in the

specified position and insert the braided

wire for grounding into the ferrite core.

Programmable

controller

GOT units

360 (14.17)

or less

360 (14.17)

or less

Unit: mm (inch

)

(1.57)

Unit: mm (inch

)

60 (2.36)

or less

60 (2.36)

or less

GOT units

Programmable controller

/GOT units

Ferrite Core

(ZCAT3035-1330)

360 (14.17) or less 360 (14.17) or less

(1.57)

Ground wires

(280 (11.0))

(3.15)

GOT unitsFerrite Core

(ZCAT3035-1330)

40 (1.57) or less

(3.15)

40 (1.57) or less

Cable shield material

Grounding braided wire

(200 (7.87))

Grounding braided wire

(50 (1.97))

Programmable contoller

Unit: mm (inch)

4.2.2 Method to connect the power wire and ground wire

1) GT1155-QTBDQ, GT1155-QTBDA, GT1155-QSBDQ,

GT1155-QSBDA, GT1150-QLBDQ, GT1150-QLBDA

Twist the 24VDC cables to connect to the GT1155-QTBDQ, GT1155-QTBDA,

GT1155-QSBDQ, GT1155-QSBDA, GT1150-QLBDQ, and GT1150-QLBDA.

The ferrite filter is not required for the 24VDC cables.

the GT1155-QTBDQ, GT1155-QTBDA, GT1155-QSBDQ, GT1155-QSBDA,

GT1150-QLBDQ, and GT1150-QLBDA unit requires an additional ferrite filter to be

attached to the 24V DC power supply cables. The filter should be attached in a

similar manner as shown in the figure opposite, i.e. the power cables are wrapped

around the filter. However, as with all EMC situations the more correctly applied

precautions the better the systems Electro-magnetic Compatibility. The ferrite

recommended is a TDK ZCAT3035-1330 or similar. The ferrite should be placed as

near to the 24V DC terminals of the the GT1155-QTBDQ, GT1155-QTBDA, GT1155-

QSBDQ, GT1155-QSBDA, GT1150-QLBDQ, and GT1150-QLBDA as possible

(which should be within 75mm of the GOT terminal).

4.2.3 Grounding the cable

Use the bus connection cable to ground the cable and grounding wire to the control

panel where the GOT and base unit are installed.

24V DC

INPUT

Up to

75mm

TDK

Braided shield

Cable clamps

GOT FG terminal

FG wire

a) For GT15-C EXSS-1 and GT15-C BS

Ground the ground wire to the FG terminal of

the GOT power supply section.

For the cable clamp attaching details, refer to

AD75CK-type Cable Clamping Instruction Manual

<IB-68682>.

1) Ground the braided shield portion of the cable to

the control panel with the cable clamp (AD75CK).

Bus connection

cable

b) For other bus connection cables Ground

the braided wire for grounding to the control

panel by tightening a screw.

5. INSTALLATION

5.1 Control Panel Inside Dimensions for Mounting GOT

Mount the GOT onto the control panel while considering the following control panel

inside dimensions.

Applicable cable

Some cables may need to be longer than the specified dimensions when connecting to

the GOT. Therefore, consider the connector dimensions and bending radius of the

cable as well for installation.

5.2 Panel Cutting Dimensions

Make holes in the panel according to the dimensions list below.

Also, ensure 10mm spaces in upper and lower parts of the panel for mounting fixtures.

Model Name A B

GT1155-QTBDQ

GT1155-QSBDQ

GT1150-QLBDQ

56 (2.20) 40 (1.57)

GT1155-QTBDA

GT1155-QSBDA

GT1150-QLBDA

38 (1.50) 40 (1.57)

No Name

1) Bus connection cable

2) Personal computer connection cable/bar code reader connection cable

152 (5.99)

120 (4.73)

140 (5.52)

Unit: mm (inch

)

153

-0

10(0.4") or more

Unit: mm (inch

)

121

-0

(6.03" )

+0.08"

-0

(4.77" )

+0.08"

-0

5.3 Mounting Position

When mounting the GOT, the

clearances shown on the right must

be left from a structure or the other

device.

Secure 50mm (1.97") or more on

the left, right and bottom sides of

the GOT to structures or other

devices.

Secure 80mm (3.15") or more on

the top of the GOT from structures

or other devices to allow good

ventilation.

If devices (such as a contactor)

generating radiated noise or those

generating heat are arranged

around the GOT, secure 100mm

(3.94") or more on the back panel.

When using the CF card, secure a sufficient distance on the left side to allow

installation and removal of the CF card.

[Securing 100mm (3.94") or more is recommended.]

5.4 Control Panel Inside Temperature and Mounting Angle

When mounting the main unit to a control panel or similar, set the display section

as shown below.

When the temperature inside the control panel is 40 to 55 (Horizontal mount),

40 to 50 (Vertical mount), the mounting angle should be in the range 60 to

105 degrees.

 The GOT will be

deteriorated earlier if it is

used at the mounting angle

other than the above.

Therefore, the temperature

inside the control panel

should be within 40 .

5.5 Installation Procedure

The GOT is designed to be embedded into a panel. Mount the GOT by following

the procedure below. For panel cutting dimensions, refer to Section 4.2. Note that

the panel thickness should be within 5mm.

1) Inserting into the panel face

Insert the GOT from the front side of

the panel.

2) Fixing the GOT

Engage the hook of the mounting

fitting (accessory) to the unit fixing

hole of the GOT and tighten the

screw until the GOT is fixed with the

mounting bolt (accessory).

The GOT will be fixed in 4 upper/

lower parts.

Tighten the mounting screw with the

specified torque.

(Failure to do so may distort the

panel and make a surface waviness

on the protective sheet.)

3) A protection film is attached on the display section of GOT prior to shipment.

Remove the film when the installation is completed.

50mm

(1.97")

80mm (3.15") or more

50mm (1.97") or more

*1 To use the CF card, leave sufficient

distances for removal and installation

of the CF card.

50mm

(1.97")

GOT

back

panel

GOT

display

section

Control

panel,

etc.

105˚

60˚

Mounting hol

Mounting

fitting

Mounting

screw

Magnified illustration

1 2 3

Komentáře k této Příručce

Žádné komentáře

Mitsubishi GT11 Specifikace Strana 2

Komentáře k této Příručce

Související produkty a manuály pro ne Mitsubishi GT11